just go into your router and assign it an ip address, turn the print server on, then navigate via web browser to the device and set up your password and ip address on the print server and you are
(username "root" and no password, the login information doesn't appear in the documented anywhere) i configured the print server to have a static ip address.
i tried installing first in the two macs but got no luck, the instructions say that you got a "server status" page, but instead you need an administrator username and password to continue.
* note: the manual doesn't seem to mention the default login -- it's user 'root' and no password.
it will ask you for a username/password.
second part you load a password into the server, unplug it and it then discovers everything wirelessly.
you will need it and your router login and password to set up this print server).
make sure you have all passwords, serial numbers, and model numbers before attempting the set up.
when asked enter the wpa (or wep) password enter the same one you use on your router.
i had to ultimately run a wep password security through the netwrk in order for the print server to connect.once all was connected, i was able to use the on demand as desired.
after this install, the netgear installation found this printer and redirected the printing port to the print server.- make sure you secure the new print server security admin password, just like
i have a netgear wgt624 v3 router and other users should note that the print server *changed the password on the router* to the default password and set the channel to 11.
i did the print server setup and then i setup the device on my 11 mbps b wireless network with wep 128-bit encryption without any problems.after the wizard i realized that by going to the devices
after the wizard i realized that by going to the devices default web page (ip address, user name, and password printed underneath the device) i could have set it up easily and more quicly as just a
my only complaint is that i can't figure out how to inbed the passkey, everytime i print a popup message asking for password comes up, it gets on my nervous after awhile.
to initially set up your handheld device, when it asks for a passkey, which is a kind of password,
the unit asks for a password which by default is blank.
, so i did not even read the manual with the exception of the default password , which is leave it empty.
in my case, i had to set my d-link password the same ("setup" tab under "administration") and under "wireless settings" make sure "security mode" is the same as d-link, i.e.
i did have difficulty finding the default password for initial setup, but once i was over that hurdle, smooth sailing.
cons: additional setup needed, small bugs in printer password use for wired pcs.
found in the dhcp client table which ip address had been assigned to the ps121, and then directed my browser there, using the default user name and password specified in the netgear documentation.
browser based configuration is easy to follow, and provides password protected access for ip address config., etc.
i just brought up abrowser window to my router, found in the dhcp client table which ip address had been assigned to the ps121, and then directed my browser there, using the default user name and
i just brought up a browser window to my router, found in the dhcp client table which ip address had been assigned to the ps121, and then directed my browser there, using the default user name and
the default login information to the internal web server is 'admin' for the name and 'password' for the password.
i did follow the directions on the cd but decided to call support when it ask for a password that was not explained in the instructions and i subsequently spent hours on the phone with linksys and
the only hitch i had was in entering my password: a call to linksys clarified that the setup procedure was looking for my router's userid instead, and the default was ''admin''.
1) halfway through the setup, the print server asked for a password.
(4) the setup wizard asks for a password for the print server.
i set up a network name for the printserver, a password, etc.
the cd that comes with the psus4 will log into the device, you can also log in manually with the ip address 192.168.1.78, password=admin (just like your router).
the default user name and password are admin admin.
other thoughts: the default password is "admin" without the quotation marks.
i popped it into safari and logged in with the default password.
cons: password protected which may not be a con but i have my network secure enough that i dont need another password for my printer but oh well...
ive had this working for a little over a year, and had an ip address change, and i couldn't remember the password to change the ip settings...
password must be 8 characters or less (unlike dlink routers)
i changed network settings to match my home setup using supplied instructions and added an admin password.
in order to reset the admin password, you have to log into the internal webserver.
cons: i attempted to change the admin password via the web gui and can no longer access the unit via the web gui or telnet.
big danger, there is no reset, so if something bad happens while changing the ip address, or if you forget the address or password, you will never get it back.
make sure you know your wireless router information and passwords.
pros: easy setup, fairly fast printing, direct-clip-on mounting to the parallel port of the printer (looks nice without cords), web or software install (i recomment the web) cons: if you set a
Compare Print Servers for Word »
Wize.com wants to improve! Will you please help by taking a quick survey?
No Thanks