if you have a firewall enabled, you'll have to temporarily disable it to allow the software to see the unit over the network.i have plugged in both a parallel port printer and a usb printer and can
make sure you turn off all firewalls or you won't be able to detect the print server on your network!!
on xp, you need to turn off the firewall to set it up, then you can turn it back on and you are golden.
tip: if your router is set to dynamically set ip addresses on your netowrk do not use the static address on the print server and remember to turn off your firewall prior to installation.
dissable your firewall before installation.
then it came to me, i recalled seeing a note mentioning to disable your firewall.
beware however that you may encouter difficulties if you are using windows xp: disable the xp firewall in network property otherwise you will not be able to setup the pc to print.
i chose a static ip address to make sure it worked with my firewall and anti-virus program.
remember to dissable your firewall software during initial setup or the setup program won't be able to find the print server.
- make sure any firewalls are disabled for installation
first you have to turn off the firewall in xp or it won't find the server.
the ps101 met my expectations.our network is one server running server 2003, nine workstations running windows 2000, two workstations running windows xp, a hardware router/firewall (does the dhcp)
it wasn't obvious to me that accessing the ps101 from a wireless laptop thru a netgear mr814 required turning off microsoft's firewall.
all the pcs have anti-virus (mcafee 8i), anti-spyware (spybot - search & destroy and ad-aware se personal pro), sygate personal pro firewall installed, and dhcp configured.
i'm using xp with sp2 and firewall turned on with no problems.
only problem was when setting it up you must turn off the microsoft firewall in order to automatically setup the server.
read pointers about turning off firewall.
i agree with what john2006 says about firewalls and the downloads.
first hurdle, read pointers about turning off firewall.
i read all of the reviews and decided to give this a try anyway and had some of the same problems as others who reviewed this product (install issues, firewall issues etc).
would be great if it didn't conflict with the windows live onecare firewall.
with this print server i'm able to print to my printer by opening a port on my firewall direct to the print server.
there is also good comedy within the cds land of troubleshooting, as it recommends you disable your firewall.
setup on windows was also easy and only complicated by the firewall software.
spent an hour with the tech rep on the phone and tried everything including disabling firewall, setting a fixed isp address and reseting device.2- pretty good support.
mine up to an hp laserjet 1300 and an hp deskjet 6540 running with a linksys wrt54gs wireless router with its dchp, wap-psk, tkip and firewall all running and it prints on both printers perfectly.
i did have to disable the firewall/antivirus to complete this task, but enabled it again once it was installed and had no problems.
you need to go there to find out how to secure the print server.- re-engage the firewalls after you complete the setup for the protection of each computer.
i had some initial trouble installing the windows software until i realized that windows was running a firewall on my system without my knowledge.
just be sure to disable firewalls (or include the ip range used on your network in a trusted zone)cons: it has two mac addresses a "wireless" mac and "device" mac" and instructions do not make it
set-up took me a while, but it ended up that i hadn't switched off my firewall for the first time that the server and my computer 'communicated'.
i had some trouble early on with setup, but that was entirely attributable to my firewall settings being so tight that my system was not relaying information back to the print server.
if it seems like it's performing slowly at first, be sure that you've given it all of the necessary clearance through your firewall, etc.
the software loaded up fine on my xp laptop but on my vista pc, if my firewall is up, any time i print i get the blue screen of death.
download the vista drivers from linksys site, (i found them there), turn off all of your firewalls, both your virus one, and your vista one, and then install the softwear.
the only issue wasn't the fault of the server but of a user not allowing the new device access through their firewall (the mac was different causing the alert).
disable software firewalls if using a router firewall.
also, is seen as a 'printserver smb printer', so may need to adjust firewall settings to permit some of netbios smb protocals.
can alternately set it up with its own ip, which will work even if you have a firewall or vpn security blocking the server software driver.
ordered this print server monday got it delivered wednesday its a great upgade for your network installation was fairly easy set it up on my 2 dells works great with my linksys firewall router and
after that it was pretty easy to config the unit and install the printer on my xp, but for my 2000 i had to add the ip of the unit to my trusted zone on my firewall before it would work.
if your using the packaged antivirus - firewall provided by some isp's, you may have to disable the firewall if it does not allow exceptions for such things
pros: allows printing without having to leave a computer on all the time.allows printing over the internet (ipp)setup was a breezecons: none - but a person who does not have much networking
Compare Print Servers for Firewall »
Wize.com wants to improve! Will you please help by taking a quick survey?
No Thanks